Why the monitor does not turn on at the hour of the computer's uptime. What work, if the monitor does not work for the hour of computer upgrade? The monitor does not turn on when

Golovna / I'll build a cleaning

Zovsіm recently vyrishuvav problem, if not pratsyuvav computer monitor. Showing injustice - not satisfied with the receptionists, then write an article about the most widespread problems that you can blame in this situation. That's why our rozmov is about those that the monitor does not turn on when the computer is turned on. As a matter of fact, I’ll tell you about a few ways to improve the situation, among them, I’m sure you know the one that will help you.

For the cob, you need to switch over, which does not work on your own monitor. Turn off the computer by pressing the "Power" button and turn it off, the docks from the system unit do not stop making noise (sound on old computers). If the computer is switched off again, then the system unit sees noise, or on the new one, there are some indicators, which mean those that the computer is switched off, but nothing is shown on the monitor, it means that the article is read further.

Important manipulations

First, start reading the article, change your mind, that the mesh filter is noted. If there is no liveliness, then you will not get the desired image on the screen. It is possible that some of the household members turned off the monitor through the button, or maybe you turned it on yourself. Perevirte, chi all harazd іz tsim.

Otzzhe, scho it is necessary to work in pershu cherga, if the monitor does not turn on when the computer is started? On some monitors, like system units, there is a button on. Sound out at the back of the monitor, sometimes sound at the side. To turn on the monitor, it is necessary to switch to the “On” position (1), for clarity, look at the image below:

To indicate that the monitor is highlighted, look at the front panel of the monitor. From below, sound the indicators flashing, behind which you can determine what voltage should go into the monitor.

Naipersha expanded the problem - tse bad contacts. Moreover, it is possible, as in the case of a wired connection to the motherboard, behind the system unit, as well as a bad contact of the video card with the motherboard, well, it’s more banal, if the contact is bad at the back of the monitor. Zagalom, it is necessary to reconsider the insults of the wires, and the wire itself, which transfers the picture to the screen and wires the wires.

There may be one underwater stone, the type of signal transmitted to the monitor. Modern video cards have two roses, which can be used to connect a monitor: white (DVI) color and blue (VGA). The remaining kind of rose, which can be seen in new HDMI monitors and when connected to it, it is important to have mercy.

If you have a DVI connection, try changing it to blue and blue. Didn't it help? Find out if the monitor is connected to the motherboard.

Vіn bude znahoditsya there at that vpadku, if at vyschezdanіy platі є vbudanovanі videoadapter. Have you gone? What do you do? Same on the right side of the video card, and on the right side of the screen, it’s bigger - you’ve burned out. You can also connect another monitor by turning on another computer, you can take a couple of credits from your friends, since you don’t have another home computer. Likewise turn on another monitor, turn off the computer, turn off the monitor and turn on the other one, and then turn on the computer.

Adjustment of the monitor

Everything is turned on, right, and you will not guess why the monitor does not turn on when the computer is turned on, then you do not need to turn it off, which setting for the monitor has been changed. Press the "Menu" button on the monitor and go for adjustments. It is necessary to change the clarity and contrast. You don’t know how to shy away from the monitor, find a helper for koristuvachs. When buying a monitor, you are responsible for giving a disk or arranging a ker_vnitstvo. For some reason, there are no reasons for this, but the Internet will help you for a joke.

For those who are not afraid to tinker in the patches, you can do it without the original discs and documents. Actually, everything made sense there. To make it easier for you to start, you can switch to the "Russian language".

If anyone will be more or less aware. Until the speech, if you bachite the menu on the screen, then everything is fine with your monitor. You can not get over yoga change.

Non-working motherboard

The next variant of the malfunction is a partial replacement of the mother's payment. At this time, the computer can turn on and start to get started, the pro monitor will not show the picture. I’ll manually check it, we’ll have to open the system unit and carefully look at the motherboard.

The requirement is not to turn off what roses are on the motherboard, where you plug in the video card, it will go bad instantly. To reconsider, you will need to install another video card and try to send an image to the monitor from it.

Everything vpiraetsya in the motherboard - it's not working, if you happen to call a specialist at home, the problem may not be on the computer screen.

Zhoriv monitor

If the monitor itself does not work, you can try yoga. Prote is not recommended to deal with them to ignorant people, it’s better to contact the service or buy a new one. It has already become a tradition that monitors rarely enjoy ordinary coristuvachi, it’s a folding process.

From which I bring the story, if I started in college at the lesson of programming, I write from the back of the monitor. At that hour, I didn’t get to know and once I ran for the vikladach, to tell me about my “radius” approach. I sat at the other office, if I flew in from such a star, I slept - and you left me for eating. Vidpovid - Nope 😉. Then, already, a mime hid in yoga guise, like a vіn bachiv a sprat of seconds to me. If you went to the office, dim mayzhe proishov, and the classmate, who sat in charge, turned yoga. A couple of seconds of laughter vikladach and seem - Well, go sit for another 😉 . The whole group laughed.

I think this story will be the beginning for you. As if I’m going to build something, I’ll need to de-energize it, so that I don’t burn the apartment or the office!

Drank at the system block

Have you done prophylaxis with your systemic block for a long time? As soon as there was a room, where the computer was located, on the contrary, the prozhdzhoї parts, then you sang a lot of saws on the pіdvіkonnyah. So the axis, the system block of the chain pump, which forges the chain saw in itself. Open the cover of the system unit and go through the saw.

important! Do not follow the mother's board's sawmill and other outbuildings. After picking up, remove the video card from the mother board and clean the contacts with a sponge for olives. Easy pressure to go through the contacts of the video card. Not required clean with a sponge for pens oskіlki vіn avenge hard particles.

You can look at the image below, as if looking, only replace the video card on the RAM image:

In one of my articles, I was talking about a video card, which will be necessary for rich readers, and will need information, go for help, so that you can read it: "".

Software security

If you have recently updated drivers and Windows is not zavantazhuetsya, then it is necessary to remove the installed software. Sounds like it is being played through an incorrectly installed driver.

To bring your computer up to you, enter the safe mode and restore the system. If you know that you have installed or updated video card drivers, then you need to remove them from your system.

About entering the safe mode for other systems, I wrote in three of my articles:

BIOS

If your computer has 2 video cards, then one is integrated into the motherboard, and the other one, then there may be a problem with the BIOS not correctly selecting attachments. You ask why the computer does not automatically recognize

To throw off the settings in the BIOS - e, by the time you yourself robit їх for Default (locked), it is enough to remove the battery in the motherboard. You can read the report about it in my article: "".

Hardware failures

The most common reason why the computer is working, but not showing the monitor is the hardware part.

The most widespread faults that lead to similar situations are the following:

- do not apply voltage;

- the signal does not reach the screen with the data cable from the PC.

Remove from the fret of the video adapter

When you exit the video card, the computer may turn on, but there will be no image on the screen. The reason for this is the presence of a viable signal. Perevіriti, chi everything is from a video card, it's easy to do it.

For whom it is necessary:

- look around visually;

- try installing it on another PC.

It often happens that if a PC master chooses not to override other components. Sometimes the video card is simply not fully inserted at the bus. You can also cause the signal on її output contacts. To that varto, pay respect to yourself for the її old look.

The capacitors that are puffed up (small bars on the board) can also serve as a sign of the way out of the fret.

Although visually everything is fine with the card, you can try to install it in another PC. Another way to re-verify is to try the display itself and get it to another personal computer. Possibly, on the right, in the newest and most necessary repairs. In both appointments, it is better than anything to get to a qualified fakhivtsya for the repair.

View of life on the monitor

Previously, a lot of extensions of the type, which can be seen, were connected without intermediary to the PC life block. The clock has gone, and the display is now inserted into the socket OKREMO, for which there is a special cable with a plug on the end.

It is not uncommon to blame the situation, if the monitor is connected to the edge, but it does not get in. In such a case, it is necessary to check the integrity of the life cable, ring with an attachment. Zrozumilo, in front of you looked like a socket.

As if one of the veins was simply torn off, there was no trace of repair, twisting. It can be caused to injury by an electrician with a strum. The most important sign of the vivacity of life on the monitor, or the re-emergence of yoga from the fret, is a light bulb that does not burn, it is placed right on the case.

The signal does not reach the data cable

Often the answer to the question is: “why, if the computer does not work on the screen?” cry without a signal at the entrance.

Similar blame for such behaviors:

- faulty data cable;

- filthy contact at the mist connection.

Sometimes it traples that the reason for the impractical display of the lucky cable. Vin can be just interruptions, rotting. It is not uncommon to trap like that, if you put on a new hotel a small piece of furniture - tables, stiltsiv. But it’s just supernaturally strong yoga, lamayuchi thin lived.

A sign of a malfunction of this type is a short notice for 1 second - when yoga is broken.

There is no sense in repairing the data cable - this process is important. The best thing is just to get a new cable at the store, the amount of goods under the product is not large.

Often after replacing the video card, or just after cleaning the insides of the PC, the driver does not carefully insert the rose data cable into the socket on the adapter. After that, the signal does not reach the screen and the image is on a new surface during the day. In order to avoid such situations, it is necessary to tighten the connection with special screws, which are on the plug.

Software faults

Crim of purely hardware problems, the appearance of the image may be related to the software part.

The most common cause of such malfunctions is:

- driver - not suitable or incorrectly installed;

- be-yakі dodatkovo installed utilities.

The main sign that the problem of image visibility is in the software part of a personal computer is the presence of an image on the display screen when it is launched and its appearance when the operating system is occupied.

Video: Black Screen

Drivers

For the work of the video adapter, I will attach it, to which vin the image is transmitted, the presence of special instructions is required. The stinks are specialized software products that are installed by the koristuvach himself. Often the reason for the failure of the PC screen is itself due to driver problems.

Reasons for vindication can be but a kіlka:

- the day of the update;

- inconsistency of instructions on the screen and video card;

- the standard security software was installed.

Most of the problem is in the fact that the PC drivers are outdated, so the possession ceases to work.

Allowing this injustice to be done simply, you can drink two ways:

- zavantazhit independently update from the official website of the owner of the collection;

When connected to the Internet, the update will be set in automatic mode, the participation of the koristuvach in this will not be required. If the screen does not work in the safe mode, then it is necessary to tweak another display.

But also, there are problems of consistency between the programs of the adapter and the PC screen. Most of the time, it appears similar after installation.

In order to avoid such situations, it is necessary to respectfully follow the changes that are being made on the PC. First, lower, install the catalysts, or similar products, work the specks for the vodkat.

Most modern operating systems have standard drivers “sewn in”, which allow you not to spend an hour on installing “native” ones. It's best to get the solution right. However, some models require installations of only "native" utilities.

If the PC screen does not work after the OS is taken over, you can go to Windows in the “protected mode” and install other drivers.

The operation is scheduled as follows:

- click on "Start";

- choose the required attachments and click on the new dvіchі;

- go to the "driver" tab;

- embossed "visible".

Then, it is necessary to run the "native" drivers installation utility immediately before activating the "PlugAndPlay" system. This function automatically restores the standard set of instructions. After the victory of all the descriptions, the next step is to restart.

Programs and utilities

Traplyatsya, that the fault of the presence of the image was installed earlier by the program and the utility. Often a lot of hardcore experiments with new software, all sorts of utilities. The stench can negatively conduct PC practice. Screen protector on display function.

As soon as the installation of a new software security image has appeared, then you can delete it through the security mode.

If this does not help, you can speed up the system update function:

- embossed on "all programs" -> "services" -> "system updates";

- follow the prompts that are indicated by the operating system.

Due to the visibility of the image on the display, there is no need to panic at any time. Most often, it’s easy to solve similar problems, you can only need help in fahivtsya in any emergency situations - stench is very rare.

And yakscho you will be tsіkava tsya statya.

Once you turn on your computer, and everything is good, the system unit is running, but the monitor screen does not work. How to work in this situation and how to solve the problem - peace be with you in our article.

For the cob of varto, say a few words about diagnostics. It is even more important to determine the nature of the problem. If the monitor does not respond when the computer is turned on - it means that a signal from the computer is not coming to the new one, if the monitor reacts to the computer being turned on, the indicator shows a connection with it, then the problem is either with the video card, or with the monitor itself. If the system itself does not show any interference, the monitor also does not show the BIOS capture, then the reason is in the robot of the computer itself.

After such an analysis, proceed to the search for the reasons for the presence of the image on the monitor and the virion of the problem.

Why is the monitor not working?

The experts gave the site the site to tell you about those, which are the most common reasons, through which the monitor does not turn on, or there is no image on the monitor.

If the monitor shows the BIOS capture, and then the black screen appears and there is no sound when the OS starts, then reinstall the system.

If the monitor will not work and after all, then try connecting it to a laptop or a video player, in order to reverse it. If the monitor works when connected to a video player and does not connect for an hour of work with a computer, then the problem is with the video card or other components of the computer. Well, when connected to another, I will build a monitor that does not work, carry yoga for repair. You can also try connecting another monitor to the computer or a current TV, if there is a problem in your monitor, if not, then look for a problem in the components of the computer.

We hope we succeeded in solving the problem, but if you didn’t get away with it, then our fahivtsy will help you with it.

Kozhen leaning in a similar situation: having planned a robot at the computer, before a reception evening watching a beloved movie, or playing an online game with friends, at the most unexpected moment you can detect a problem - the monitor does not turn on! The screen is greedily filled with black, and the monitor itself does not give any signs of life. At such a moment, you may feel a little panic - why bother? The project is on fire, but it is impossible to practice!

If it’s not a sleeping screen, you can blame it like a program, so it’s a hardware crash

Really, the problem can be serious. However, first of all, go to the nearest computer service with a monitor in a frame, otherwise you can find out why the monitor does not turn on, and you can also get used to it if you go to the office. Could it be enough?

There are a number of reasons why, through the fact that when the computer is turned on on the screen, you can not get the image. Let's look at the most widespread reasons:

Daily connection to the border.
Pulling forward causes - the cable is incorrectly connected to the computer socket.
"Junk" nalashtuvannya.
Move driver.
I changed the video card.
Monitor failure.
On the right side of the motherboard.
Sawing down the system unit.
Blame the operation.

Daily connection to the border

Quite often, coristuvachi do not give respect to the camp of the wires of the computer, which are so impersonal. The very same thing can cause interruptions in the life of the monitor - when the control is moved from one place to another, the tension of the wires, when trying to get it wrong, it is possible to turn on the monitor in the middle. What to work: it is necessary to reverse the plugged-in cable into the socket, and from the back side - plug it into the monitor. Might be necessary to replace the cable. Well, at startup, the light on the monitor lights up, but the screen, like before, does not, then the next thing to do is to look for reasons.

Cable incorrectly connected to the socket of the system unit

Two options are possible here: when turned on, a socket is selected and the cable is lightly screwed. What work? The system block can have two video cards - the integrated one is discrete. Such a mood needs a friend; If you change the wiring, you need to unscrew the fixing bolts and reconnect the cable to the system unit correctly.

"Junk" nalashtuvannya

If the computer's robots are blamed for failures, then it will also be blamed on the monitor's robots. Yak yogo "do not work". What work? As a matter of fact, you can correct the situation by vicoristing another rose, or a safe entry, to clear the alarm and allow the monitor to turn on. In addition, for the presence of two video cards in the system block, it is necessary to change the settings in the BIOS, so that the integrated card can be found at the switched-off station.

Pіdvіv driver

So buvay, just recently a new program was installed for the video card of the computer, or the driver was updated. Then the video card may not "home" with the new firmware. What work? It is necessary to see the update and remove the large driver in the robot.

Vіdmovila video card

Poshkodzhennya can be through a mechanical insertion at the internal attachments of the system unit. For example, through the cleaning of the computer, or as a result of the removal of the video card, it was suddenly brought back. As a result, there may be damage to її robots. What to work: it will be necessary to reinstall again.

Even though it is already broken, but, as before, the monitor does not turn on, then the problem may be in the video card itself. To reconsider, you need to bring the card to the next rose of the mother's payment. In this case, the monitor is connected to the integrated card, which is connected to the discrete card in front of the computer.

Monitor failure

Try diagnosing the malfunction of the monitor itself and you can also help solve problems when it is turned on. Zokrema, I’ll show you a reconciliation, de pardon when connected, or injustice through various reasons. If anything you can work directly with the singer.

Right in the motherboard

If the motherboard is faulty, the screen will not show anything, wanting the computer to work better. If you blame the suspect on a non-working motherboard, you need to get into the system manager and resolutely learn її. Possibly, the location of the video card is broken. Then you need another video card, if you want to check the visibility of the image on the screen. And there is another option for the development of a subdivision, if the motherboard does not intervene without a change, if it happens to be.

Sawing down the system unit

Many people do not know what it is necessary to keep clean not only the computer style, mouse, keyboard and monitor screen, but also regularly clean up the middle of the system unit. You ask: is there more of a closed space? I don't know. The case of the system unit can be opened, to serve for ventilation of the "guts" of the computer. Until then, the cooler, which is constantly working, "inflates the situation", which will absorb the penetration and accumulated saw on the parts of the computer.

How to clean the computer from the saw? Elementarily - a pilosos. Wine is in a be-yak_y apartment, so it doesn’t matter to hurry up with a brown butt prilad. And bring melancholy to the axis! Golovne, correctly pilososity - neatly, without sticking around the elements of the system. If all of you drank zіbrany, you can boldly accept for an individual cleaning of your mother's pay. For the help of a great stationery bag for olives (not for pens!). The mother board needs to be removed from its own.

The operation is to blame

As well as problems in the operating system of a computer, there are also options. For example, when the monitor is turned on, it shows the BIOS system, but it does not work further, if you want the sound to be captured. Otherwise, viruses have penetrated the system, as well as the hour of installing new programs that start the functioning of the video card. What to work: here you will need to deal with such a skin cause okay.

When the BIOS is enabled, but without a sound accompaniment, it will be enough to re-upload.

If you already had to work all over again, then it would be better to distort it, like a working monitor, for which you should bring it to a laptop or a video player. If the monitor works when connected to the video player, then the problem is in the video card or in the computer settings. Otherwise, the monitor is not working properly and needs to be repaired by the facsimiles. So it goes, when another monitor is connected: if it doesn’t show the VIN, it needs to be sorted out with the computer, if the image is there, then there are problems in the monitor itself.

What else?

It is possible to oxidize metal contacts in the cable. Solovі "drunk" and shortness of good are taken for additional alcohol. Children should follow carefully, so as not to mess up the rough and soft structures. Deformed pins will need to be trimmed with an awl or a hairpin. If you didn’t get into trouble without a cost, then, unfortunately, you have to replace the cable. And even though it is already selected, then to avoid oxidation in the future with gold-plated contacts.

So what else, even if the monitor is turned on, it still needs to be repaired, it’s definitely wrong and needs to be repaired or replaced. Ale, don’t get angry. Tse does not mean that the whole computer is out of whack. You can always try to fix the breakdown or speed it up with another monitor or computer. And the master of repairing computer equipment will deal with the hacking of the monitor.