How to check the correctness of the work of the laptop fan Self-diagnostics of overheating of the laptop. Open that fan clogged with a saw
If you suspected that you were guilty of overheating, if I put it in a laptop, it is necessary to reverse the operation of the fan. For whom it is necessary to use additional utilities.
you need
- - Speed Fan.
Instruction
These methods can be tested both for laptops and for stationary computers. Let's talk about two utilities, for the help of which you can adjust the speed of wrapping, and also change the main problems that you blame on your own.
cpu fan control
Speed up with Speedfan. You'll get data about all the ventilators shown in the PC and you can see them. We need to turn respect into two blocks:
- shvidkіst wrapping;
- available cooler regulators.
The first block indicates the quantity of work speed, the other - the ability to regulate. The program itself designates, which cooler is known, to that person (CPU - processor and GPU - video card) already signed.
Alece in the best option. Buvaє, that the fans are not recognized by the program, the list will be seen as unknown. In this vipadka, you can speed up using the tik method. It is necessary to change the value of the skin Pwm doti, as if you do not realize that the noise is changing.
Just like coolers don't show up, it doesn't mean that they don't, because they don't stink. Most of the time, such a cooler does not support software regulation of speed. Report as below. In case of nalashtuvanni, insure: the value, as you designate for the cooler, to be deprived of the permanent independence of the venture.
If you think that these installations have started working immediately after the system is started, it is necessary to check the checkboxes in the checkbox in the Configure → Options block:
Adjustment of fans in the video card (MSI Afterburner)
This program is recognized exclusively for setting up the fan in the video card. That's the bug that regulates the number of wrappers is only one. A cob of vins of eminence, that for the cob of yogo it is necessary to include.
After that, as required parameter is set, press "Apply". On the right is a monitor that displays all the information on the graph. Here you can check all the changes in the temperature of the video card, speed and speed. When the selected parameters are chosen, it is also possible to automatically switch to the beginning of the robotic system. For this, you need to check the Apply overclocking at system startup checkbox.
Vishcheperelіchene - less than the main possibility of the program. It also has an option that allows you to specify, for some parameters, the video card fan is to blame. For which you need to go to Settings → Cooler and enable auto mode.
Show up schedule. Vertically everything shows the speed of work in windows, and horizontally - the temperature. With the left mouse button, if the graphics can create a point, by setting the necessary parameters in this way. If the settings have become irrelevant, the stench is turned on by the “User Define” button.
What is work, what is not working? Cause that way to sleep
Like mova go pro desktop computer, then the most common problem is to fix the cooling of the processor.
The coolers can be connected with different connectors: 3-Pin and 4-Pin (PWM). For additional utilities, only a few fans can be regulated. Іz trypіnovim tse do not work. Therefore, call on the price when buying coolers for the processor.
If this is the problem of vinyl on a laptop, then there are two options.
Blocking the ability to regulate the processor in front of the picker. There is no solution here.
If the laptop is not a gamer, then there is only one cooler for the processor and the video card, so it’s the same as the graphics embedded in the processor. For such laptops, it's a good idea to zastosuvat software methods regulation.
Visnovok
For a stationary computer, everything is correct. If the software regulation does not help, you can always change the cooler https://itgroup1.ru. If you look at laptops, then the gamers are most likely to be improved, the office average varsity is 50/50, and the axis from the built-in graphics is richer.
Laptop overheating common cause up to service center. At the shortest point the laptop is markedly "galmuy". At hirshomu - high temperature lead to breakage. Causes of failure: incorrect operation, ventilation clogged with a saw, worn out thermo-interface and the construction failed. Let's try to figure out what causes the causes of overheating, and how to deal with them.
What does it consist of
The laptop cooling system consists of a fan (or fans), radiators and ventilation openings on the case. Typical design - the middle radiator snakes through the processor and video card chips, leading to the fan, which looks hotter through the opening at the laptop case. At the contact points of the radiator, there is a chip, between them there is a ball of thermal interface: a thermogut or thermal paste.
How to calculate the temperature
Modern laptops can diagnose themselves independently. Considering that the temperature exceeds normal, the laptop performance decreases. It seems about such a thing that "the computer has become a galmuvati." In more complicated situations, the laptop is turned on in an emergency and, in the event of an attack, alert about the problem. But only on the intellect of a laptop, it’s not varto. You can independently determine the high temperature "by eye". As you can see, the laptop heats up much stronger, lower when buying, you need to get used to it. Whoever is closer to a scientific pidhіd - it is recommended to install a thermometer program. For example, HWMonitor. To gain respect, which you need to work in a navantage camp - when watching a movie, when working with 3D graphics, or for an hour.
HWMonitor shows temperature of chipset (THRM), processor cores (Core #0 and Core #1), videocard chip (GPU Core) and hard drive(HDD) Maximum storage temperature per model, and guide figures:
- processor - 75-85 °;
- videocard - 70-90°;
- winchester - 50-60 °;
- chipset - up to 90°.
If the temperature exceeds the upper boundary, it may be necessary to seek help from a specialist.
Causes of overheating and necessary come in
Nevdala design of the cooling system
It's a pity, buvaє, scho overheating due to the design features of the laptop. Call such a laptop to get very hot from the first day of work, or after a short period of operation, because. the most sympathetic to the reasons, about which will be discussed below.
No need to get angry. To build on your table an awkward design, like in the photo. Just lift the rear end a little. It is necessary to improve the circulation again and the temperature may drop by 5-10 degrees. The way you can zastosovuvat whether de - pіdіyde zvichayna book.
A greater effect can be achieved with the help of a special cooling pad. Support for construction with fans. With them, it is possible to achieve a decrease in temperature by 5-15 degrees. Z nedolіkіv - large dimensions and nebhіdnіst have zvnіshny zhivlennі vіd sockets or USB.
"People's minds" to pronounce and original solutions.
Incorrect operation
A laptop can be used only on hard surfaces - on a table or on a stand. At the extreme stand - on knees (want to sit comfortably in such a position for a long time). All on the right at the ventilation openings. If the laptop is standing on a table on small legs, it will be easier to walk around under the case. When a laptop is installed on a soft surface (near a bed, on a sofa, on a tablecloth), the ventilation doors open up. Do not come in hotter, do not get colder, and the temperature in the middle of the body rises.
The recommendation is even simpler: misuse your laptop. Practice at the table. And if you don’t feel like living without a laptop in your bed, beat the tables and stands. Stop, for example, you can buy in Іkeї.
Open that fan clogged with a saw
Tse v_dbuvaєtsya practically with usima laptops. Drank accumulates in the middle of the case, clogs the ventilation openings and impairs the operation of the fans. It is recommended to carry out scheduled cleaning after the end of the warranty term and skin offensive rock. Cleaning can be carried out only in the middle. Everyday saw, a special “computer” or a hard homemade one, cannot pull the whole saw through the clogged door.
And also razbirannya-skladannya vimagayut singing knowledge. I would like to be theoretical. Sudno posterіgatime, how the motherboard cracked through those that were screwed in the wrong order.
Replacement of thermal interface
As we have already said on the cob, in the areas of the contact of the radiator with the chips between them, there is a thermogummie or thermal paste. When replacing a thermal interface, not only knowledge is important, but also a beginner. A little too thin, a thin or uneven ball can lead to the fact that the laptop heats up even more, lower earlier. As a rule, I replace the thermal interface by cleaning the saw.
Ventilation system out of order
The laptop ventilation system consists of two parts:
- The heating system is a set of thermotubes and radiator grilles. Designed for transferring heat from crystal processors to radiators, where the heat rises through the flow.
- The fan itself. Some laptop models may be different.
Most often, the fan itself comes out of the fret, sound through the overheating, conjure the bearing, or it will break up with the hour and begin to “thrill”. In "smart" laptops, with a faulty fan, at the start of the BIOS, you see a notification about the pardon of the cooling system. To diagnose such a malfunction in budget laptops, put your hand up to the outer grille of the radiator in case of significant interference, the air flow and fan noise should be noted about the fan malfunction.
Another widened inadequacy of the cooling system is the inadequacy of thermotubes. Thermotubes cease to conduct heat from the processor to the radiator grille. If the fan is working on the bottom covers, the laptop will have a cold sweat again, but the processor will overheat. This incompatibility is not safe for a laptop if the processor or the motherboard goes out of order.
But the photo shows that the thermotube is cut in the middle plate, there is no heat input in the processor
There is only one way to deal with such inaccuracies - by replacing.
So, as your laptop becomes too warm, change your mind to do it right. If problems occur during the next hour on hard surfaces - bring them to the service. For the time being, there is only a slight increase in temperature. Albeit not doing anything, it can lead to serious physical damage to the possession. Better prevention.
With the active vikoristanny of any laptop, zocrema, in the summer hour, koristuvachs can often stick with the problem of overheating. Such an "embarrassment" can lead not only to insignificant subversion of the operating system, but also to the omission of the main details system unit- processor (read our article about those), video card and motherboard. With the method of lowering the temperature in the middle of the laptop, it is possible to turn on the primus fan when required. About those who know how, read our article.
To respect the fact that in front of them how to win back whether it was manipulations with a laptop, it is necessary to change the cooler as a whole. Also, do not forget to check the fan for cloudiness, even through an excessively bought saw, you can make a mistake operational work shovels.
Also, let's look at the nutritional information about the primus fan starting the fan behind the auxiliary BIOS system. In practice, when starting up, I will build it regardless of the model or brand, and start the cooling process, which can easily confirm the presence of the noise.
Please note that in certain situations the fan may not be installed correctly due to polarity connection problems. It is possible to reconsider again at the same time when the cooling system is started when the laptop is turned on. Bring a thread or a piece of paper to the ventilation opening and unzip it, so that the object becomes kolivatsya. At this time, the system works correctly. In the other case, the object will stick to the opening, which confirms the problems with refrigeration.
The ability to control the functions of the fan for additional commands from the BIOS is often updated.
Obviously, for a cooler laptop, you will need to turn on Turbo mode. However, you are also to blame for the fact that the wear resistance of the fan itself during continuous operation is significantly reduced and can lead to breakage.
Note! Not all laptops may be able to install a fan for an additional BIOS, so in some cases it can happen special programs, Mova about yaki pide far.
Starting the fan for the help program SpeedFan
Also, since your laptop does not support the adjustment of the speed and speed of the fan through the BIOS, you can speed up cost-free program speedfan. To improve the ventilation rate for additional software, you need:
- Get SpeedFan on the website of the retailer or any other source.
- Install SpeedFan on your laptop following the installer's instructions.
- Run the program through the shortcut on the desktop.
- Go to the section "Pokazniki". You can set the air pressure of the fan for each distribution.
- In addition, this program allows you to set the criteria for the work of other components of the laptop. At the “Configuration” section, you can specify the temperature of the hard drive, processor and motherboard, as well as the temperature parameters for which the system will tell you about overheating.
Note! Cream SpeedFan, on the Internet you can find other similar programs. For example, the AMD OverDrive utility will allow you to customize whether any criteria in the robotic system should be able to see if your laptop has an AMD chipset installed. For Intel processors, there is also a specially developed software - Riva Tunes.
Running a fan on a laptop for help with Windows commands
Operational Windows systems, Starting from the 7th version, there may also be utilities for managing the difficult criteria of the laptop. For their customization it is necessary:
- Select "Control Panel" and select "Electric Life".
- Choose whether there is a power plan and then go to the distribution box, you will need to know the item “Change additional parameters eating".
- In the list of settings, select the item "Processor recovery".
- For the new one, select the subparagraph "The policy of cooling the system."
- Set the parameter "Active" for all settings. Press "Zastosuvati", and then "OK".
Now the fan will be constantly switched on, which will allow you to escape from the cold overcooling of the system and those other “colds”.
Video - How to set up automatic cooling on a computer or laptop?
It’s not the same, but, sing-songly, the situation is known to the skin informed motorist: the car is “boiling”, the arrow of the engine temperature indicator, without daily visible reasons uphill. What work? The best thing is to start the car and turn off the engine, so that overheating can lead to jamming, with the necessary “principles” of a major overhaul. Well, now, it’s time to guess how to diagnose the cooling system, zocrema, how to check the radiator fan. It is necessary to change the bottom of the radiator to the bottom of the radiator: if the wine is cold - the thermostat is not right, if it is the same hot, if it is the top - everything was clear, more for everything - the fan is not working.
Sliding from simple to folding, for the most common reasons. For example, the integrity of the zapobіzhnik. The replacement did not help - to change the practicality of the electric motor by connecting the fan directly to the battery. At the time of the exit from the fret - less than a change. Rewire the temperature sensor by removing the new terminal and shorting it out. If the fan is in such a position, it is necessary to replace the sensor. Even though it doesn’t help - I’ve ripped up the lancers, having checked the fan relay and the electrical wiring. Sometimes, it's easier to lay down a new guide, lower the knowledge of the old one.
Whether it’s water, it’s always to blame for the memory, which is violating food, how to repair, repair the radiator, how to change its tightness, how to turn on the radiator, and many others, connected with the cooling system of the engine, you need to do everything possible to ensure the safety of the rules of technology. This is connected with the temperature increase and the pressure of cold water in the system, and with the toxicity of water. In addition, it is necessary to take care of the protection of the elements of the system, especially for the integrity of the pipes of the heat exchanger of the radiator. Well, if the manager of the car solves the problem, if you replace the heater radiator, then in the first place you will know the interior details of the cabin. Tobto, it is necessary, the cream of safety technology, be careful in robots in order not to damage the internal design of the car. By changing the heater radiator, it is necessary to ensure the tightness of the ducts of the passage of the cold air. Lifting the antifreeze in the saloon, the stars of the siding of the skin are not the best sight.
The radiator of a car is a well-thought-out design solution that protects the impersonal operational factors. To that, in front of a motorist, problems can be blamed for the partial repair of the cooling system, washing, laying small holes, then nutrition - like a radiator, is not guilty of being put up, not formulating. It is impossible in the home minds of "brothers and brothers" a radiator that has reached full practicality. As such, the power of viniclo is better for everything, the hour has come to replace the radiator with a new one. Tse will be better, but better possible breakdowns dviguna - and definitely cheaper. Choosing a new radiator, a lot of things to be done, which is better to take - copper-coloured aluminium. It's important to give someone food. Vihodyachi z reparability - better than the middle metal, yakі can be soldered in the home minds. Aluminum has a higher thermal conductivity, lower price. Varto realistically evaluate your financial ability and repair skills.
The axis of the world in terms of home microclimate systems is already a dilemma - how to choose bimetal radiators of scorching, which will increase the metalness of steel with a high coefficient of heat exchange aluminum. The emergence of new technologies is not followed. Maybe, and motorists, if you choose an alternative choice, and get radiators from the repairability of the middle ones and the price of aluminum?
