How to enter bios on msi laptop or want to use uefi? How to update bios on MSI motherboard? Update bios on msi motherboard
In this article, there are ways in which you can reset the BIOS on your computer or laptop in case of any problems with the robot.
Korisnі articles on the topic
Sometimes, for a variety of reasons, it is necessary to reset the BIOS "a computer (motherboard). In these settings, more parameters are saved, as they are used for the operation of the computer and all devices. The following describes how many ways you can on the value for the lock:
Skimming BIOS settings through the BIOS menu
The best way to do this is to allow access to the BIOS if the computer is enabled. For which it is necessary, when the computer is turned on, press a special button, which will allow you to enter the BIOS setup. The most common use of the button is the Del (Delete) button.
Further away, lie down in the form of the motherboard’s motherboard, and the BIOS "a in it. It’s not guilty to fold any BIOS in the motherboard visually, take a look at the pictures, to explain, to the instructions for the skin type BIOS"a.
Skip bios settings in Award Bios
Use the keyboard to navigate to the "Load Optimized Defaults" item. We press Enter, then on the confirmation confirmation is selected by the arrows of the keyboard "OK". We press Enter.
Now go to the Save & Exit Setup item. Pressing Enter, after which the computer is guilty of resetting, and resetting the BIOS is thrown off.
BIOS upgrade from Phoenix Bios
Keyboard arrows (left, right) go to the top menu tab under the name "Exit".
There we know the item "Load Setup Defaults". We select it with the arrows up, down and press the Enter key. To appear at the end, in which case it is necessary to confirm your request, reset the BIOS - select "OK", then press Enter.
Now you need to select the "Exit & Save Changes" item.
Let's go there, press Enter, to ask for confirmation - select "OK", and press Enter again. The computer is guilty of rebooting and resetting the BIOS.
Skip BIOS settings in ASRock UEFI BIOS
At the top menu, go to the "Exit" tab.
We select the item "Load UEFI Defaults".
On the "Load UEFI Defaults?" prompt "Yes".
Now select Save Changes and Exit.
On the bottom of the screen you see "Save configuration changes and exit setup?" prompt "Yes".
Once the BIOS has been adjusted, the BIOS will be reset, and the computer will be rebooted.
Skip BIOS settings in ASUS UEFI BIOS
Mother's ASUS boards There are two UEFI interfaces - one is found on old motherboards that were released until about 2014, the other is found on all motherboards that are released. Therefore, if you do not visually recognize the interface of your BIOs / UEFI, do not hasten to close the side with the instructions, but simply move on.
First option
At the bottom right corner, push the "Default (F5)" button and click on it.
To appear at the end of the day with a request for confirmation of the victory. Select "OK".
Now we have a brand new menu in front of us. Right upper codend we know the "Exit / Advanced Mode" button, that is pressed on it.
Select "Save Changes & Reset".
The computer will be reset, and the BIOS will be reset.
Another option
Click on the F5 key or on the " Default (F5) at the bottom of the screen.
We choose " OK or press the enter key (Enter).
Let's choose " Save&Exit(F10)(or press the F10 key).
I'm pushing again OK"or the Enter key.
Skip BIOS settings in MSI UEFI BIOS
Basically BIOS menu select "Mainboard settings" ("Settings").
We select the "Save & Exit" item.
Select "Restore Defaults" from the menu.
Appear at the end with a confirmation request - "Load Optimized Defaults?". Reply "YES".
Now you need to log out, saving the BIOS settings. For which, go to the item Save Changes and Reboot.
For food, why do we want to restart - Save configuration and reset - "YES.
Once the computer is rebooted, and the BIOS settings will be reset to standard settings.
Skimming BIOS settings by way of battery drain
For the cob it is necessary to turn on that computer.
For which it is necessary on the back side of the system unit to know the life block and turn it off special button. So we won’t take it for a ride on the life of the new one, it’s obov’yazkovo in that moment, as if there’s no life.
All you need to know is a round battery of CR2032 format, most of it is placed at the bottom of the motherboard. In order to drain the battery, you need to press a special trim.
After the battery is drained, it is necessary to press the life button for 10-15 seconds. Shards of the system block of noise, then it will not turn on, then it will be enough to discharge the accumulated electricity in the computer. At this point, the BIOS settings will be reset.
Now you can close the system unit by turning the cover on the plate, plug in the life cord and turn off the life unit, after which you can turn on the computer.
Skidantnya nalashtuvan BIOS through a jumper
Znestrulyuєmo system block, having switched on the block of life with a special vimikachem, roztashovan the entrance to the air supply.
Dali znіmaєmo kryshku system unit i popraplyaєmo vseredinu kom'yutera. Now there is a special jumper on the motherboard. It looks like a blue (for the most vipadkivs) jumper, like it’s arrived up to two pins, in total there can be three pins. Sound, this jumper is signed as "Clear CMOS", "CLR", "CLEAR", "PSSWRD".
To skip the BIOS, you need to move the jumper by one pin to the side. Tobto. the back of the jumper closes pin 1 and 2 - we need to tie it to pin 2 and 3.
After that, it is necessary to press the computer's life button for 10-15 seconds, for the residual electricity discharge, which is stuck in system block. Once the BIOS has been adjusted, it will be discarded.
Good afternoon. This article is related to the BIOS setup program, which allows you to change the basic system settings. The settings are saved in non-delimited CMOS memory and are saved when the computer is powered down.
ENTER THE PROGRAM SETUP
To go to the BIOS program, open the computer and press a key. . To change advanced BIOS settings, press the Ctrl+F1 combination near the BIOS menu. The menu of additional parameters in the BIOS is displayed.
KERUVAL KEYS
<
?>
Jump to the front menu item
<
?>
Transition to the next point
<
?>
Transfer to the point livoruch
<
?>
Move to the right hand point
<+/PgUp>
Increase the numerical value of the setting or choose another value from the list
<-/PgDn>
Change the numerical value of the setting or select another value from the list
DOVIDKOVA INFORMATION
Golovna menu
The description of the selected installation is displayed at the bottom of the screen.
Zvedena storіnka nalashtuvan / Storіnki nalashtuvan
When pressing the F1 key, a window appears with a short hint about the possible options for setting that recognition of the correct keys. Shchob close the window, press
Main menu (from the butt of the BIOS version E2)
When you enter the BIOS setup menu (Award BIOS CMOS Setup Utility), the main menu (small 1) appears, in which you can choose from eight sides to setup and two options for exiting the menu. Choose the required item for the help of keys with arrows. Press to enter the submenu
Fig.1: Golovne menu
If you don't know how to configure, type Ctrl+F1 and look for it in the advanced BIOS settings menu.
Standard CMOS Features
Everything is on the other side standard customization BIOS.
Advanced BIOS Features
On this side, there are additional parameters of the Award BIOS.
Integrated Peripherals
On this side, all the peripheral outbuildings are installed.
Power Management Setup
On this side, the energy-saving mode is established.
PnP/PCI Configurations
On this side, you can configure resources for extensions
PCI and PnP ISA PC Health Status (Computer Monitoring)
On the left side, the temperature values, the voltage and the frequency of the wrapping of the fans are displayed.
Frequency/Voltage Control (Frequency and voltage regulation)
On the third side, you can change the clock frequency and the processor frequency multiplier.
For reach maximum productivity set "Top Performance" to "Enabled".
Load Fail-Safe Defaults
Bezpechnі nаshtuvannі for promchannyа garantirovat pratsezdatnі system.
Load Optimized Defaults
Optimization of the adjustment for the promotions leads to the optimal performance of the system.
Set Supervisor password
On this side you can set, change or remove the password. This option allows you to access the system and update the BIOS, or even to the BIOS.
Set User password
On this side you can set, change or remove a password that allows you to access the system.
Save & Exit Setup
Save money on CMOS and out of the program.
Exit Without Saving
Skasuvannya all changes and exits from the program of adjustment.
Standard CMOS Features
Figure 2: Default BIOS settings
Date (Date)
Date Format:<день недели>, <месяц>, <число>, <год>.
Day of Tuesday - the day of Tuesday is assigned by the BIOS to the entered date; yoga cannot be changed without a middle.
Month - the name of the month, from sichnya to the chest.
Number – day of the month, from 1 to 31 (or the maximum number of days per month).
R_k - r_k, from 1999 to 2098.
Time (Hour)
Hour Format:<часы> <минуты> <секунды>. The hour is entered in the 24-year format, for example, 1 year of the day is recorded as 13:00:00.
IDE Primary Master, Slave / IDE Secondary Master, Slave (IDE Disk Drive)
For each distribution, the parameters of the disk storage devices installed on the computer (types Z to F) are determined. There are two options for setting the parameters: automatically and manually. When manually assigned the accumulative parameters, you set the accumulative accumulator, and in automatic mode The parameters are assigned by the system. Please note that the information entered is due to the disc type.
If you enter the wrong information, the disc will not work normally. If User Ture is selected, you will need to remember to hover below the item. Enter data from the keyboard and type
CYLS - Number of cylinders
HEADS - Number of heads
PRECOMP - Pre-compensation for an hour of recording
LANDZONE - head parking zone
SECTORS - Number of sectors
If one of the hard drives is not installed, select NONE and press
Drive A/Drive B (floppy drives)
For each distribution, types of floppy disk drives A and B are set, installed on the computer. -
None - Floppy drive not insertable
360K, 5.25in. Standard 5.25 inch PC-type floppy disk with a capacity of 360 KB
1.2M, 5.25 in. 5.25" AT type floppy drive with 1.2 MB high-capacity write capacity
(3.5-inch floppy drive, as long as mode 3 support is enabled).
720K, 3.5in. 3.5-inch drive with double-sided recording; capacity 720 Kb
1.44M, 3.5 in. 3.5-inch drive with double-sided recording; capacity 1.44 MB
2.88M, 3.5 in. 3.5-inch drive with double-sided recording; capacity 2.88 MB.
Floppy 3 Mode Support (for Japan Area)
Disabled The default floppy drive. (Nalashtuvannya for zamovchuvannyam)
Drive A Floppy drive A supports mode 3.
Drive Floppy drive In support mode 3.
Both Floppy Drives A and Trim Mode 3.
Halt on
The price of the adjustment is determined, when such pardons are revealed, the system will be zupined.
NO Errors The system will continue to be taken care of, no matter what. Notices about pardons appear on the screen.
All Errors The request will be interrupted if the BIOS shows a pardon.
All, But Keyboard Zavantazhennya will be interrupted for any kind of pardon, for a blame for a keyboard failure. (Nalashtuvannya for zamovchuvannyam)
Ail, But Diskette The business will be interrupted for any pardon, for the fault of the floppy drive.
All, But Disk/Key The zavantazhennya will be interrupted for any pardon, for a fault of the keyboard or disk.
Memory
At this point, the memory expansion is shown, which BIOS is used for the hour of the system self-test. It is not possible to change these values manually.
Base Memory
With automatic self-testing, the BIOS displays the base (or primary) memory installed in the system.
If the system board has 512 Kbytes of memory installed, the screen will display 512 K, if the system board has 640 Kbytes of memory installed or larger, 640 K will be displayed.
Extended Memory
During automatic self-testing, the BIOS will show the size of the system installed in the extended memory. Expanded memory - tse operative memory with addresses greater than 1 MB in the addressing system of the central processor.
Advanced BIOS Features
Fig.3: Advanced BIOS tweaks
First / Second / Third Boot Device
(First/other/third exciting addition)
Floppy Capturing from a floppy disk.
LS120 Drive from LS120 drive.
HDD-0-3 hard drive type 0 to 3
SCSI Access from SCSI add-on. Downloaded from a ZIP drive.
USB-FDD Capture from floppy drive with USB interface.
USB-ZIP Download from ZIP-attachment with USB interface.
USB-CDROM Drive from CD-ROM with USB interface.
USB-HDD Hard disk drive with USB interface.
LAN Entrance through a local network.
Boot Up Floppy Seek
At the process of self-testing system BIOS determines the type of floppy drive - 40-track or 80-track. A 360 KB drive is 40-track, and a 720 KB, 1.2 MB and 1.44 MB drive is 80-track.
Enabled BIOS determines the drive type - 40 or 80 tracks. Keep in mind that the BIOS does not recognize disk drives 720 KB, 1.2 MB and 1.44 MB, all stinks are 80-track.
Disabled BIOS does not show the drive type. 360 KByte disk drive installation time No notification will be displayed on the screen. (Nalashtuvannya for zamovchuvannyam)
Password Check
System If you do not enter the correct password when starting up the system, the computer will not be taken over and access to the settings side will be blocked.
Setup If you do not enter the correct password when starting up the system, the computer will be taken over, and access to the setup pages will be blocked. (Nalashtuvannya for zamovchuvannyam)
CPU Hyper-Threading
Disabled Hyper Threading mode disabled.
Enabled Hyper Threading mode is checked. To pay attention to the fact that this function is implemented less at a glance, as the operating system maintains a rich processor configuration. (Nalashtuvannya for zamovchuvannyam)
DRAM Data Integrity Mode
The option allows you to set the pardon control mode for operational memory yakscho vikoristovuєtsya memory type ECC.
ECC ECC mode disabled.
Non-ECC The ECC mode does not override. (Nalashtuvannya for zamovchuvannyam)
Init Display First
AGP Activate the first AGP video adapter. (Nalashtuvannya for zamovchuvannyam)
PCI Activate the first PCI display adapter.
Integrated Peripherals
Fig. 4: Budovanie peripheral attachments
On-Chip Primary PCI IDE
Enabled Enabled IDE controller 1 channel enabled. (Nalashtuvannya for zamovchuvannyam)
Disabled Disabled IDE controller for 1 channel.
On-Chip Secondary PCI IDE
Enabled Enabled IDE channel 2 controller enabled. (Nalashtuvannya for zamovchuvannyam)
Disabled Disabled IDE channel 2 controller.
IDE1 Conductor Cable (Type of stub connected to IDE1)
ATA66/100 A ATA66/100 type cable is connected to IDE1. (Check if your IDE device and cable supports ATA66/100 mode.)
ATAZZ Before IDE1, a loop of the ATAZZ type is connected. (Check that your IDE device and cable support ATA3 mode.)
IDE2 Conductor Cable (Type of loop connected to SHE2)
Auto Automatically recovers the BIOS. (Nalashtuvannya for zamovchuvannyam)
ATA66/100/133 A ATA66/100 type cable is connected to IDE2. (Check if your IDE device and cable supports ATA66/100 mode.)
ATAZZ Up to IDE2, a loop of the ATAZZ type is connected. (Check that your IDE device and cable support ATA3 mode.)
USB Controller
If you do not disable the USB controller, disable this option.
Enabled The USB controller is enabled. (Nalashtuvannya for zamovchuvannyam)
Disabled USB controller disabled.
USB Keyboard Support
When connecting a USB keyboard, set the value of this item to “Enabled”.
Enabled The USB keyboard has been enabled.
Disabled USB keyboard support disabled. (Nalashtuvannya for zamovchuvannyam)
USB Mouse Support
For different USB mouse connections, set this item to “Enabled”.
Enabled USB mouse support enabled.
Disabled USB mouse support disabled. (Nalashtuvannya for zamovchuvannyam)
AC97 Audio (Audio controller AS'97)
Auto The AC'97 audio controller is omitted. (Nalashtuvannya for zamovchuvannyam)
Disabled Disabled AC'97 audio controller.
Onboard H/W LAN
Enable Enable Fencing Controller enabled. (Nalashtuvannya for zamovchuvannyam)
Disable Disabled wakeup controller.
Onboard LAN Boot ROM
Vykoristannya PZP vbudovannogo twill controller for zavantazhennya system.
Enable The function is enabled.
Disable The function is disabled. (Nalashtuvannya for zamovchuvannyam)
Onboard Serial Port 1
Auto BIOS sets port 1 address automatically.
3F8/IRQ4 Enable wake-up of last port 1 by setting its address to 3F8. (Nalashtuvannya for zamovchuvannyam)
2F8/IRQ3 Enable wake-up of last port 1 by setting its address to 2F8.
3E8/IRQ4 Enable wake-up of last port 1 by pressing its address 3E8.
2E8/IRQ3 Enable wake-up of the last port 1 by pressing its address 2E8.
Disabled Disable last port 1.
Onboard Serial Port 2
Auto BIOS sets port 2 address automatically.
3F8/IRQ4 Enable wake-up of last port 2 by setting its address to 3F8.
2F8/IRQ3 Enable wake-up of last port 2 by setting its address to 2F8. (Nalashtuvannya for zamovchuvannyam)
3E8/IRQ4 Enable wake-up of last port 2 by pressing its address 3E8.
2E8/IRQ3 Enable wake-up of the last port 2 by pressing its address 2E8.
Disabled Disable port 2.
Onboard Parallel port
378/IRQ7 Enable wake up LPT port by setting it to address 378 and retrying IRQ7. (Nalashtuvannya for zamovchuvannyam)
278/IRQ5 Enable wake up LPT port by setting it to address 278 and acknowledging IRQ5 reset.
Disabled Disable the LPT port.
3BC/IRQ7 Enable LPT port wake-up by setting its 3BC address and acknowledging IRQ7 reset.
Parallel Port Mode
SPP Parallel port works in normal mode. (Nalashtuvannya for zamovchuvannyam)
EPP Parallel port operates in Enhanced Parallel Port mode.
ESR Parallel port is available in Extended Capabilities Port mode.
ECP+EPP The parallel port works in ECP and EPP modes.
ECP Mode Use DMA
3 ECP mode DMA channel 3. (Closing setting)
1 ECP mode DMA channel 1.
Game Port Address
201 Set the address of the game port 201. (Setting for locking)
209 Set the address of the game port to door 209.
Disabled Disable the function.
Midi Port Address
290 Set MIDI port address 290.
300 Set MIDI port address 300.
330 Set the MIDI port address to 330. (Closed)
Disabled Disable the function.
Midi Port IRQ (MIDI port interrupt)
5 Assign IRQ 5 to the MIDI port.
10 Assign IRQ 10 to the MIDI port.
Power Management Setup
Fig. 5: Nalashtuvannya keruvannya living
ACPI Suspend Type (ACPI Suspend Type)
S1(POS) Set the S1 pointing mode. (Nalashtuvannya for zamovchuvannyam)
S3(STR) Set the S3 scrutiny mode.
Power LED in SI state
Blinking Live mode indicator (S1) blinks. (Nalashtuvannya for zamovchuvannyam)
Dual/OFF
a. As a rule, the one-bar indicator flashes, in the S1 mode it turns off.
b. As a result, there is a double-color indicator, which changes the color of the S1 mode.
Soft-offby PWR BTTN (Computer Soft-Off)
Instant-off When you press the life button, the computer will beep at once. (Nalashtuvannya for zamovchuvannyam)
Delay 4 Sec. To turn off the computer, press the next button for 4 seconds. When the button is pressed for a short time, the system will switch to the mode of recovery.
PME Event Wake Up
Disabled Wake-up on PME disabled.
ModemRingOn (Wake up on a modem signal)
Disabled The modem/local network wake-up function is disabled.
Enabled Function enabled. (Nalashtuvannya for zamovchuvannyam)
Resume by Alarm
At the Resume by Alarm item, you can set the date and hour of the computer notification.
Enabled Enabled the computer enable feature.
If the function is marked, enter the following values:
Date (of Month) Alarm: Day of the month, 1-31
Hour (hh: mm: ss) Alarm: Hour (hh: mm: cc): (0-23): (0-59): (0-59)
Power On By Mouse
Disabled The function is disabled. (Nalashtuvannya for zamovchuvannyam)
Double Click Wake up the computer when the mouse is under pressure.
Power On By Keyboard
Password To unlock the computer, you must enter a password of up to 1 to 5 characters.
Disabled The function is disabled. (Nalashtuvannya for zamovchuvannyam)
Keyboard 98 Even though there is a button on the keyboard, the computer will turn up when pressed.
KV Power ON Password
Enter Enter a password (from 1 to 5 alphanumeric characters) and press Enter.
AC Back Function
Memory After the renewal of life, the computer turns in the same camp, in which it has changed wines before the death of life.
Soft Off (Nalashtuvannya for zamovchuvannyam)
Full-On
PnP/PCI Configurations
Fig.6: Setting up PnP/PCI attachments
PCI l/PCI5 IRQ Assignment
Auto Automatic reset for PCI 1/5 attachments. (Nalashtuvannya for zamovchuvannyam)
3, 4, 5, 7, 9, 10, 11, 12, 15 Assigned to PCI 1/5 add-ons IRQ 3, 4, 5, 7, 9, 10, 11, 12, 15.
PCI2 IRQ Assignment
Auto Auto-shutoff for PCI 2. (Lockup setting)
3, 4, 5, 7, 9, 10, 11, 12, 15 Assigned to PCI Attachment 2 IRQ 3, 4, 5, 7, 9, 10, 11, 12, 15.
ROS IRQ Assignment (Assignment for PCI 3)
Auto Automatic reset for PCI 3.
3, 4, 5, 7, 9, 10, 11, 12, 15 Assigned to PCI 3 add-on IRQ 3, 4, 5, 7, 9, 10, 11, 12, 15.
PCI 4 IRQ Assignment
Auto Auto-shutoff for PCI 4. (Lockup setting)
3, 4, 5, 7, 9, 10, 11, 12, 15 Assigned to PCI 4 add-on IRQ 3, 4, 5, 7, 9, 10, 11, 12, 15.
PC Health Status
Fig.7: Computer monitoring
Reset Case Open Status
Case Opened (Roztin case)
If the computer case does not open, the Case Opened item shows No. As the case letter is broken, at the Case Opened item it appears Yes (So).
To drop the sensor reading, set the “Reset Case Open Status” item to the value “Enabled” and see from the BIOS to save the settings. The computer will reboot.
Current Voltage (V) Vcore / VCC18 / +3.3 V / +5V / +12V
At this point, the main voltages in the system are automatically checked.
Current CPU Temperature
At this point, the temperature of the processor is displayed.
Current CPU/SYSTEM FAN Speed (RPM)
At this point, the frequency of wrapping the fan in the processor and the case is displayed.
CPU Warning Temperature
Disabled Processor temperature is not monitored. (Nalashtuvannya for zamovchuvannyam)
60°C / 140°F Warning is seen when the temperature exceeds 60°C.
70°C / 158°F Warning is seen when the temperature is over 70°C.
80°C / 176°F Warning is seen when the temperature is over 80°C.
90°C / 194°F Warning is seen when the temperature exceeds 90°C.
CPU FAN Fail Warning
Disabled The function is disabled. (Nalashtuvannya for zamovchuvannyam)
SYSTEM FAN Fail Warning
Disabled The function is disabled. (Nalashtuvannya for zamovchuvannyam)
Enabled When the fan teeth are visible, the front is visible.
Frequency/Voltage Control
Fig.8: Frequency/voltage adjustment
CPU Clock Ratio
How the processor frequency multiplier is fixed, this option is in the daily menu. - 10X-24X The value is set depending on the clock frequency of the processor.
CPU Host Clock Control
Note: If the system hangs before the BIOS takes over, check for 20 seconds. At the next hour, the system will reboot. When resetting, the value of the base frequency of the processor will be set, as it is set for locking.
Disabled Disable the function. (Nalashtuvannya for zamovchuvannyam)
Enabled Activate the function of turning on the base frequency of the processor.
CPU Host Frequency
100MHz - 355MHz Set the base frequency of the processor between 100 and 355MHz.
PCI/AGP Fixed
To adjust the AGP/PCI clock frequencies, select 33/66, 38/76, 43/86 or Disabled for each item.
Host/DRAM Clock Ratio
Respect! If the value of this item is incorrect, the computer cannot be taken advantage of. At the same time, the next step is to reset the BIOS.
2.0 Memory frequency = Base frequency X2.0.
2.66 Memory frequency = Base frequency X 2.66.
Auto The frequency is set according to the SPD data of the memory module. (Value for locking)
Memory Frequency (Mhz)
The value is determined by the base frequency of the processor.
PCI/AGP Frequency (Mhz)
Frequencies are set indefinitely according to the value of the CPU Host Frequency option or PCI/AGP Divider.
CPU Voltage Control
The CPU voltage can be increased by 5.0% to 10.0%. (Value for locking: nominal)
DIMM OverVoltage Control
Normal The voltage of the memory is equal to the nominal voltage. (Value for locking)
+0.1V Memory voltage increased by 0.1 Std.
+0.2V Memory voltage increased by 0.2 Std.
+0.3V Memory voltage increased by 0.3 Std.
Tіlki for dosvіdchenih koristuvachіv! Improper installation can lead to computer failure!
AGP OverVoltage Control
Normal The voltage of the video adapter is higher than the nominal voltage. (Value for locking)
+0.1V The voltage of the video adapter has been increased by 0.1 st.
+0.2V The voltage of the video adapter has been increased by 0.2V.
+0.3V The voltage of the video adapter has been increased by 0.3V.
Tіlki for dosvіdchenih koristuvachіv! Improper installation can lead to computer failure!
Top Performance (Maximum Productivity)
Fig.9: Maximum productivity
Top Performance (Maximum Productivity)
To achieve the highest system performance, set Top Performance to Enabled.
Disabled The function is disabled. (Nalashtuvannya for zamovchuvannyam)
Enabled Maximum productivity mode.
Increased productivity of the robotic hardware components. On the robot of the system in which mode it is necessary to add both hardware and software configuration. For example, the same hardware configuration itself may well work under Windows NT, but not work under Windows XP. Therefore, to blame problems with reliability or stability of the system, it is recommended to enable this option.
Load Fail-Safe Defaults
Fig. 10: Installation of non-furnace installations behind the lock
Load Fail-Safe Defaults
Safe adjustment for promotion - the value of the parameters of the system, the most secure from the point of view of the practicality of the system, and also ensure the minimum security code.
Load Optimized Defaults
When choosing this menu item, the standard settings of the BIOS parameters and the set of microcircuits are set, which are automatically assigned by the system.
Set Supervisor/User Password
Fig.12: Enter password
When you select a menu item, you will be asked to enter a password at the center of the screen.
Enter a password up to 8 characters long and type in
To tell the password, press at the prompt to enter a new password
The BIOS setup menu allows you to set two different passwords: administrator password (SUPERVISOR PASSWORD) and koristuvach password (USER PASSWORD). If passwords are not set, be-your koristuvach can take access to the BIOS settings. Once a password has been set, for access to all BIOS settings, it is necessary to enter the administrator's password, and for access to only the main settings - the password of the koristuvach.
If you select the “System” parameter in the advanced BIOS settings menu, under the “Password Check” item, the system will ask for a password when the computer is skinned, or you can try entering the BIOS settings menu.
If you select “Setup” in the advanced BIOS settings menu at the “Password Check” item, the system will no longer ask for a password when you try to enter the BIOS settings menu.
Save & Exit Setup
Fig. 13: Save money and leave
To save changes and exit from the menu, press "Y". To turn around to the menu, press "N".
Exit Without Saving
Fig.14: Exit without saving change
To exit the BIOS setup menu without saving changes, press "Y". To turn to the BIOS setup menu, press "N".
Past stats were talking about those. And at once I will tell you how to nail Computer BIOS for Windows installation from a disk or a flash drive.
1. What is BIOS and UEFI
Leather motherboard special program for setting up a computer and adjusting parameters other outbuildings. This program is flashed (programmed) on a special microcircuit on the motherboard and is therefore called firmware.
Previously, all motherboards had a firmware, as it was called BIOS, as a small simple graphical interface with white letters on a blue background and a bula was surrounded by functionality. For example, in the BIOS it is not possible to select a teddy bear, to select a language and to have daily graphic elements (pictures) in front of the BIOS memory chip. Also, BIOS motherboards did not support disks larger than 2 TB through the older disk layout system (MBR).
At the same time, a lot of motherboards can have a new type of firmware, UEFI titles, which can be improved by a better graphical interface with a beautiful background, painted buttons, the ability to choose a movie (including Russian) and other extensions. For example, support for a new type of disk distribution (GPT), which allows you to win hard disks larger than 2 TB.
What type of firmware can your motherboard can be recognized from the helper before it, on the website of the laptop motherboard selection tool, and also visually for an hour to enter the program setup setup. The Setup program is also programmed into the motherboard and can be used to change BIOS or UEFI settings.
2. How to go to BIOS Setup
To enter the Setup program, you need to press the Delete button on the keyboard once you have upgraded your computer. On some motherboards and laptops, the keys "F2", "F10" or "Esc" are used. You can read the click button in the notifications that appear as soon as the computer is turned on.
At the text view
Have a graphic look
If you can't read it, press the "Pause" button on the keyboard to start engrossing. You can continue to take advantage of the onslaught of any keys. As soon as you press the key assigned to enter Setup, you will immediately go into the motherboard setup program.
Classic BIOS
UEFI interface
3. The Basics of the Setup
3.1. Keys keruvannya
The Setup program is a set of different parameters, grouped on four tabs, and fallow in recognition. On the right, or at the bottom, there will be a description of the keys, for the help of which all the dii will win.
To move between tabs, sound the arrows "right", "left" on the keyboard. To move between rows in the middle of one tab, the arrows "down", "uphill" are used.
To change the value, you need to go to the additional arrows on the required field, press the “Enter” key, and then, after the additional arrows, select a new value from the menu that appears. For whom, the keys “+”, “-” or “Page Up”, “Page Down” can also be played.
To turn to the level uphill or to the front side, press the Esc key. The Esc key on one of the head tabs means to exit from the BIOS without saving the settings, which you will need to confirm or be prompted to exit.
AT Setup programs With the UEFI interface, you can win all the games for the help bear.
3.2. Save money
This is an important moment. After all necessary adjustments go to the "Exit" tab, wrap the "Exit and Save Changes" item with arrows "Enter".
You can save the hacking more simply and more quickly by pressing the F10 key on the keyboard and confirming your decision. This key works in rich versions of BIOS, UEFI and is often indicated in prompts (below or right-handed).
3.3. Skasuvannya nalashtuvan
If you have already changed it, or if you didn’t make sure that the changes were corrected, then go to the Exit tab and select Exit and Discard Changes (Exit and Discard Changes) or press the Esc key until the prompt appears "Yes").
3.4. Reinvention nalashtuvan
To restore all the settings for the optimal values for the promotion, go to the “Exit” tab and select “Load Setup Default” (“Set Up the Settings for the Promotion”). If so, you can immediately change the settings, or simply exit the BIOS with the saved parameters (Exit and Save Changes or F10).
4. Variants of interest
Insert an advanced disk or USB flash drive on the computer on which you plan to install Windows. Now, in order to install Windows, it is necessary to configure the BIOS (or UEFI) for the help of the Setup program to download from a disk or a flash drive. Also, for whom you can choose a special entrancing menu of the motherboard ( boot menu). The remaining option is simpler and more convenient, but we can look at the offensive ways.
5. Customized BIOS
5.1. Change of priority
Go to the Boot or Boot tab.
Install a DVD-drive or a flash drive first in the order of exciting attachments.
If you install Windows from a disk, then the first step is to select an attachment of the "ATAPI CD-ROM" type, naming the name of the drive or drive model. For example, CDROM:PM-HL-DT-STDVD-RAM GH22NP (not LG DVD drive).
If you are planning to install Windows from a flash drive, then select the "Removable Dev." type first. or name the flash drives from the designations of the virobnik. For example, "USB: Patriot Memory" (flash drive "PATRIOT").
Transcend JetFlash 790 8Gb
Others can stand hard drive, which is indicated as Hard Drive, HDD or interface to which connection port, selector and disk model. For example, "SATA:3M-SAMSUNG HD502HJ" (this is a 500 GB "Samsung" hard drive with a SATA interface).
Please note that there may be other items in the Boot distribution that are considered to be priority, such as Hard Disk Drives or Removable Device Priority.
It's also necessary to stink, so the DVD-drive or the flash drive was in the first place.
If you have two hard disks, then you are more to blame for the one on which you install the system. But at this time, I recommend one of the disks to turn it on, so that the swindle possible pardons in the system installation. Yogo can be connected after installation.
In the Setup program with the UEFI interface, everything works in the same way. Shukait split "Boot" or "Advantage", know there your DVD-drive or flash drive and take it to the top priority of the acquisition. Plus, for whom you can win a bear, which is simpler and more convenient.
5.2. Robotic SATA controller mode
Tse, in principle, is not so important, but if someone cries out food, then I’ll clear it up. SATA disks can be used in a mixed mode with older IDE disks and more frequently AHCI mode. AHCI gives a small increase in the productivity of a hard drive with a multiplier one-hour recovery to a new one. Such a robotic disk mode is mainly found on servers and for a typical home computer it is practical.
When the BIOS is configured, you can choose the SATA controller mode.
Tsі nalashtuvannya can be found in different places and deschko vіdіznyatis in names, but skіz one principle. You are encouraged to use the IDE mode or the new AHCI mode.
In general, it's recommended to disable the IDE's summation mode for Windows XP, but you can't use SATA drivers and just don't turn on the hard drive, which won't allow you to install Windows. Drivers can be installed in the installation Windows distribution Ale sensu doesn’t have it, that’s why it doesn’t matter to the speed of the robot, but you can add problems.
Є simplest i manual way booting from a DVD-disk or a flash drive for both BIOS and UEFI - booting for help Boot Menu (Menu Boot).
You can use the keys F8, F10, F11, F12 or Esc for the wiki menu. Often you can watch them at the prompts on the cob screen of your computer. More information can be found from the instructions on the website of the motherboard reader of either a laptop, by searching the Internet or using the tick method.
As soon as you click on the computer, press it, press the Boot Menu button, the docks will not appear in the menu for choosing an exciting add-on.
For help, the arrows "down" and "up" go to the DVD-drive or flash drive and press "Enter".
Sandisk Cruzer
The advantages of this method are obvious - you don’t need to dig into the BIOS, you don’t need to then turn the BIOS settings back (if you don’t want to reset the language) and click on the menu only once, since it’s not necessary after the installation of Windows. In addition, changing the Boot Menu does not change BIOS or UEFI settings.
7. Problems from the entanglements
Friends, in zv'yazku z tim, scho bugatioh blamed problems іz zavantazhennym pіd іnstalyatsії Windows і deyakі wrote pro tse in komentary, I vyrіshiv zrobiti okremia rasdіl, de zbrav vіdomі menі ways vyrіshennya tsikh problems.
- As the computer’s attention is right on the cob itself and ask to press F1, after which you enter to the BIOS, then you have a better battery on the motherboard (it may take an hour), problems with the processor cooler (it’s off the hook, it wasn’t connected) or hard disk (pardon in SMART).
- As soon as the PC is notified, the message “Reboot and Select property Boot device or Insert Boot Media in selected Boot device and press a key” appears, which means that the area on the disk is occupied or the flash drive is not found, or it is hidden. Try to get started from the installation disk or flash drive for the Boot Menu help (divided 6 articles), as it will not help to build the new boot drive again for the help of the Windows USB / DVD Download Tool.
- As soon as you restart your computer, the Windows installation will start from the start, change the upgrade disk or flash drive and restart the computer, the installation will continue from the hard disk.
- Turn on all USB devices connected to the computer (flash drive, 3G modem, smartphone, printer). Get rid of the mouse, keyboard, DVD-ROM or USB flash drive, for which you can install Windows.
- If you have a small number of hard disks, then enable all disks in the motherboard, moreover, on which Windows installation will be installed.
- Throw off the standard BIOS settings (described in this article).
- If the installer does not download the disk, otherwise the pardon 0x0000007B will appear in the BIOS, change the SATA controller mode from AHCI to IDE in the BIOS, or back.
- If the computer is skin-locked, or the laptop itself enters the BIOS, or it opens the capture menu, then install BIOS option Boot Pop Menu at the Disable / Vimkneno camp (yakscho є).
- Disable Fast Boot in the Advanced branch of the BIOS, and in the Boot branch, set the Launch CSM option to the Enable setting.
- For the BIOS Boot, change the EFI (UEFI) capture mode to Legacy (yes, yes).
- Set BIOS option secure boot at the camp Disable / Vimkneno (like є).
- Select the version of the installed Windows from the BIOS (likely є).
- Like you have a laptop, one Windows version to be installed, but otherwise they didn’t help you for the sake of updating the BIOS, go back to support or to the forum of the virobnik. You can also help update the BIOS, after which additional options may appear (item 8-12).
- With the possibility of a DVD-disk, as with flash drives, there are a lot of problems.
- Work from .
- Insert the flash drive into the USB 2.0 socket on the back panel of the computer (motherboard) or the USB 2.0 sockets of the laptop. The USB 3.0 plug is not required.
- Try speeding up the Boot Menu, as described in paragraph 6 of the article. This way is simpler, better, lower, setting the priority of advancement in the BIOS and you can determine whether your USB flash drive should be downloaded by the computer.
- The lower confirmation on the black screen is to talk about those that the computer freezes at the moment of downloading to a flash drive or a hard drive. Yakscho without a flash drive zavantazhenya ide far away, then right exactly in it.
- If your computer does not download a flash drive, or if you do not want to get involved with it, download a DVD-ROM or another flash drive to install it.
- Since there is no such possibility, then change the type of flash drive znіmny nose» to the hard drive with the help of the BootIt Next Generation utility, format it with the HP USB Disk Storage Format Tool and rebuild the hack with the help of the Windows USB/DVD Download Tool. All these utilities you can order below in the "Essential" section.
- If the problem is already cleared up after you choose to install Windows, hurry up to fix the BIOS (item 7-12). To see the old ones from the disk, or to dig for the help of an exciting disk. Acronis Disk Director.
- If the installer tells you that you can't install Windows to disk, try vikonati or go back.
I'm guessing that the F10 key is set to exit the BIOS from the savings.
8. Posilannya
At the next article, we can look at how to install it, that one.
Sandisk Cruzer
Transcend JetFlash 790 8Gb
Sandisk Cruzer
In our time, laptops, nettops, monoblocks, and stationary PCs have become more often used in warehouse systems, so that the optical drive cannot be damaged. Not surprisingly, even the digital industry has practically seen the expansion of various content on optical storage devices.
Through those that do not have an optical drive in the computer, the coristuvachi have become guilty of collapsing from the installed operating system on a new one. Most often when installing the OS through DVD drive koristuvach without spending the annual upgrades at the BIOS, so the first investment in the investment at the new DVD-ROM. The only option for systems that cannot install DVD-ROMs is to install from a flash drive.
To install the OS from a USB flash drive or from a portable USB HDD, required install options for exciting USB devices in BIOS. In order for our readers to be able to independently engage in USB accumulator, we prepared the material, in which on the butts we describe the process of setting BIOS for downloading from flash drives for other systems.
Preparing our USB storage device
Nasampered for capturing a flash drive help BIOS, її it is necessary to work zavantazhuvalnoy. For example, take a licensed disk with Windows 7 and create a new iso image. The image can be downloaded using the help of DAEMON Tools or Alcohol 120%. Also, the original image of the disk with the licensed SIM can be downloaded from the official website Microsoft, having your own license key.
After otrimavshi image file, let's proceed to the next step. This package includes the folding of an exciting USB flash drive for additional utilities Rufus. This utility was picked up for a reason. Identity utilities Rufusє those who won't be able to burn zavantazhuvali USB flash drives for both the original BIOS and for UEFI BIOS. Get the utility Rufusїї її її її її її ї ї ї ї ї ї ї ї ї ї ї ї ї ї ї ї її її її її її є їє ії її ії ії ії ії її ії іnstаlyаtsії.
In the previous program, what was seen, it is clear that in the first combo list " Attached» A 16 GB flash drive is displayed. If I select USB, I will add it, you need to specify the program Rufus way to iso image Windows 7. For which one press the button with the laser disc icon and select the image. After that, press the Start button and check for the completion of the creation of our exciting USB storage device.
This is how exciting flash drives for Windows 8, 10 and XP, and other operating systems are created. Especially handy for help Rufus capture a flash drive from Windows XP. It’s worth mentioning that more ways to create an exciting flash drive with Windows XP are even more foldable for great koristuvach PC. W Rufus And, navpaki, accumulating with Windows XP is easy and fast.
After that, as an exciting flash drive is created, you can proceed to install or reinstall the SIM card for help. Therefore, in an offensive application, we describe the process of capturing a flash drive we created on a computer with a UEFI BIOS.
Using a USB storage device on a computer with a UEFI BIOS
On computers with a UEFI BIOS trim, you can tweak the Windows OS both with a new BIOS trim and without it. For example, let's take a computer that does not have an optical drive and the choice of faults with the motherboard upgrade MSI A58M-E33 with support UEFI BIOS. Now we need to install a USB flash drive, created earlier than our computer. For swedish zavantazhennya s nevnogo storable drive in motherboards under keruvannya UEFI BIOS is special boot menu. This menu allows you to select the first accumulator without changing the BIOS main menu. On the other computers boot menu you can click through F12 and F11 . Our view on MSI A58M-E33 motherboard boot menu call through the F11 key.
From which menu you can see the item “ UEFI: KingstonDataTraveler 2.0PMAM» ta « KingstonDataTraveler 2.0PMAM". If we select the first item, then Windows 7 will be restored with support UEFI BIOS and if it’s different, then for the help of a great BIOS. After choosing the first or the other item, the installation files will be revealed.
Significantly, we have created an exciting USB storage device for additional proprietary software Microsoft Windows USB / DVD Download Tool, then we could not install an OS that supports the UEFI BIOS, it's possible to create an exciting flash drive, because it can't support UEFI.
Rush away. Now let's try to fix USB attachment from the BIOS of the MSI A58M-E33 motherboard. For which computer, press the Del key when starting the computer. Tse zavantazhit BIOS motherboard.
At the main BIOS window, go to the tab " Settings”, after which the menu is adjusted. For this menu, you need to select the item "". After this choice, the gains will be improved.
In these parameters it is clear that the first vanishing attachment is a hard drive.
So that our flash drive was vandalized at the start of the system, we set the item “ UEFI USB Hard Disk» first on the list.
After that, it is necessary to save the BIOS configuration and reset the computer. Now, at the start of the system, the first thing to do is to grab a USB storage device with a UEFI BIOS support. To select a flash drive with an operating system without a UEFI BIOS support, you need to insert the item " USB Hard Disk» to the top of the list in BIOS settings.
From the butt you can see how easy it is to snap boot menu This interesting BIOS configuration of the MSI A58M-E33 motherboard. Similar rank seems to be the BIOS upgrade on new motherboards from other manufacturers.
Now it's possible to take advantage of USB storage on an old computer with a Phoenix BIOS
Phoenix BIOS created by Phoenix Technologies. Tsey BIOS will be popular on old computers. For help Phoenix BIOS you can also zavantazhitisya with a flash-capacity. For example, let's take a SAMSUNG R60 laptop, which has a support Phoenix BIOS. Like on most computers, press the Del button and go to settings Phoenix BIOS.
For our task, we need to go to the tab " Boot". On this tab, select the item “ Boot Device Priority”, after what we can use in the menu to fix the avant-garde outbuildings.
We need to select the USB flash drive first in the list, as shown below.
After the change, our exciting flash drive will be the first to take advantage of when the system starts. In the same way, you can put and run a flash drive on a large PC under the Phoenix BIOS password.
Now it's possible to take advantage of USB storage on an old computer
Let's look at the launch of a flash drive on a PC under AMI BIOS. by the American company American Megatrends Incorporated, which is why the abbreviation in the name AMI is so prominent. This BIOS is used to buggy PCs through the start logo at system startup.
Let's open the computer and let's move on to nalashtuvan for the help key Del. At the bios window, we need to go to the “nashtuvan” item.
After the vykonanyh dіy vіdkriyutsya nashtuvannya, yakі allow you to set the priority of accumulative devices at the start of the system, including flash drives.
In the same rank, you can put and run a flash drive on a larger computer under AMIBIOS backup.
Problems with the implementation of the installed task on AMIBIOS and Phoenix BIOS
Koristuvachi arcs of ancient laptops and stationary computers can be fixed from the problem of launching an exciting USB add-on.
This problem is due to the fact that on older computers under AMIBIOS and Phoenix BIOS there is no support for launching USB devices at system startup. Therefore, the only zavantazhuvalnym will have an optical drive.
Another nuance in case of our zavdannya may be different versions of AMIBIOS and Phoenix BIOS, which may look different. The head office can have an interface and other roztashuvannya nalashtuvan. In this way, it’s not varto to be confused, to that the configuration of the configuration of the entanglement of the retailers is far from good and you can always know that by analogy with the butts described above.
Now it's possible to capture from a USB storage device on a mini PC
New mini PC Compute Stick Since the company Intel has quickly gained popularity among the cores, to those with a computer with Windows OS on board, which, for the dimensions of everything in a kilka, outperforms the splendid flash drive. Through such dimensions, there are no more interfaces, like in stationary PCs and laptops. For example, no RJ45 interface and no interface for digital DisplayPort monitors.
Intel shards Compute Stick Supplied with a front mounted operating room Windows system 8 or 10, then most of the coristuvachiv do not have problems with the installation on the new OS. Ale, how to get out of the situation, if the OS has suffered from viruses and the removal of system files.
In this situation, a flash drive is additionally lucrative boot menu Bios. For example, take an analogue of Intel Compute Stick I'll call Meegopad T02. To reinstall Windows on your computer, you need to download the OS image on the official website of Meegopad T02 www.x86pad.com. After downloading that creation exciting flash drives, put її on Meegopad T02. Let's take a look at Meegopad T02, getting into the boot menu Bios for the help key F10.
AT boot menu you can choose a USB flash drive and install it for additional Windows. For a permanent capture of a flash drive at system startup, you can open the BIOS and set the capture of other USB storage devices to a new priority.
Pіdbivaєmo pіdbag
Having read the guidance, put it another way, an ordinary coristuvach PC can easily set the priority exciting flash drives for systems with different BIOS versions. Having learned how to install a flash drive first when you are interested, you will understand how quickly and manually you can install different operating systems on your PC.
Hopefully, our article will help you get started from a flash drive and install an operating system, and also help you install it on your computer, so that you can’t use an optical drive.
Video on the topic
Finishing our series of articles about updating the BIOS, we will tell you about those, how to update the MSI BIOS, even motherboards may have their own peculiarities!
Updating the BIOS for an add-on equipped with an MSI motherboard is carried out in the following way:
- be restored specific model your mother's pay;
- reality version updates ts_kavoi system for you;
- vikonati їhnyu bezperednyu installation.
If you know exactly the model of your possession and the version of the system for reinstallation, then you have no more charge on your motherboard under the MSI brand. The firmware you need can be downloaded both on a computer and on a portable device.
How to upgrade the BIOS to the MSI brand for an additional flash drive?
It is possible to launch the software for you version of the software update for the introduction-vivodu directly from the working table.
For the efficiency of this operation, you can use a special Click BIOS II interface, which is suitable for work with attachments like a Taiwanese picker. At the “Utilities” branch, you will find the correct way to install the M-Flash program from a flash drive, as it will help you to update the software for entering and exiting.
Dana specialized utility prompt you to speed up with the "Update Bios" option. With the help of the flash drive, the required update file is selected, the next steps are taken from the official site of the compiler, and then it is installed in automatic mode. Before proceeding with a computer, it is recommended to restart yoga.
At the same time, MSI live update 6 is available. To learn about a special utility, for help you can find out the version of your motherboard, vicorist has distributed "Information about the system". 
Takozh given program help you in real time to check the presence current updates I’ll build it for my own, I’ll grind it manually or automatically. If you choose the first option, you will need to check the box next to the other item “MB Bios” before the scanning cob. 
Razbiraemosya in models of motherboards and utilities from the Taiwanese compiler.
Warto remember what the abbreviation means, what it means to upgrade the BIOS for what we try to install, how to name the company that specializes in the manufacture of motherboards.
It sounds like Micro-Star International. In this way, do not talk about a specific version of the motherboard, but rather about the whole family. For example, you may have MSI z270 a pro or MSI h110m pro vd on your computer.
You can change your motherboard model, so that you can upgrade the input-output system every year, in various ways, for example:
Have a wonderful day!
